An HMI display hierarchy arranges process screens in levels, from a plant overview down to single instruments, so an operator can reach any pump in a few clicks. The model defined in ANSI/ISA-101.01 has four levels: a process area overview, process unit screens, equipment detail screens and diagnostic screens, each showing less plant and more detail.
I draw SCADA screens for water networks and process plants, and I settle the hierarchy before placing a single symbol. Colour has its own post, the HMI colour scheme.
How many HMI screen levels do you need?
The ISA model uses four, and I keep four on any plant with more than one process area. A 2018 Idaho National Laboratory report for the US Department of Energy describes them like this:
| Level | What the screen holds |
|---|---|
| 1, process area overview | The operator’s whole span of control, mainly critical performance values |
| 2, process unit | Surveillance and control of one unit, with trends that show the desired range |
| 3, unit detail | One piece of equipment or one control scheme, for detailed diagnosis |
| 4, diagnostic | Subsystems, individual sensors or components |
ISA-101.01-2015, Human Machine Interfaces for Process Automation Systems, applies across continuous, batch and discrete industries. The count matters less than keeping the branches alike. NUREG-0700 Revision 3, the US Nuclear Regulatory Commission’s human-system interface review guidelines, notes that when every major branch has the same branches below it, users can predict one branch from another. If Pump station 1 has a pumps, a tanks and an energy screen, every station gets those three, in that order.
What belongs on an HMI overview screen?
An overview screen holds the operator’s whole area of responsibility and the few values that say whether it runs well. The Idaho National Laboratory report describes Level 1 as the span of control of the whole plant, built mainly from critical performance parameters for a rapid assessment of status, and usually read-only.
On a water network I draw each station as one block: outflow, reservoir level, pumps running and an alarm count. Each block links to that station’s Level 2 screen, so the overview is also the way down to every station. I leave commands off it, because a pump should be started where its pressures and alarms are in view.
How should operators navigate between HMI screens?
Operators go down by clicking the equipment, return to the top in one action and move sideways without climbing back up. NUREG-0700 and the Idaho National Laboratory report cover each move:
- Down: displays link to higher and lower levels, so a station block opens its Level 2 screen and a pump there opens its Level 3.
- Up: every screen has a direct path back to the overview, such as a home button.
- Sideways: Next and Previous move along one level, from Pump 2 to Pump 3 without going back through the station screen.
- Location: the title states the screen’s place, and a breadcrumb shows the path taken.
- Speed: NUREG-0700 gives 0.5 to 1.0 second as the maximum response to a request for the next page, with under 0.25 seconds preferred.
Hermetry connects field devices to live dashboards, rules and alerts: IoT telemetry and SCADA in one platform. A process drawing holds at most 200 symbols, and the SCADA troubleshooting page suggests splitting a large plant into areas linked with card actions or detail pages. Open a board opens another board with its parameters preselected, the boards you came through show as a breadcrumb, and Go back or the browser’s back button returns through them (see card actions and drill-down boards).
Level 2 and Level 3 screens usually start from the plant’s drawings; how to read a P&ID covers those symbols. On a water network I make each station a Level 2 branch; see also remote monitoring of pumping stations and reservoirs.
Frequently asked questions
What is a display network in an HMI?
NUREG-0700 defines a display network as a group of display pages and their organisational structure, and notes that the structure usually follows a hierarchical, sequential or relational principle. In a process HMI I use a hierarchy and add relational links on top, such as an alarm that opens its equipment’s screen.
How should HMI screens be numbered?
Give each screen a code that shows its place. NUREG-0700 describes four-digit codes where the first digit marks the major branch (1000, 2000) and the second the next level down (2100, 2200 within 2000), so 2300 visibly sits under 2000.
Should the alarm list sit inside the display hierarchy?
I keep the alarm list outside it, one click from every screen, with each alarm linking to its equipment’s screen. NUREG-0700 asks for more than one way to reach a display, and the alarm list is the second way I give operators.

