Water tank level monitoring comes down to three methods: a non-contact sensor, ultrasonic or radar, mounted above the water; a submersible pressure transmitter hung near the bottom; and float switches as an independent backup for high and low levels. The right choice depends on tank access, condensation and foam, and what the reading drives.
On a reservoir that feeds a pump station, the level reading decides when pumps start and when someone gets called. For water utilities, I let that shape the choice more than the sensor price.
Ultrasonic vs hydrostatic level sensor for water tanks
An ultrasonic sensor measures the distance to the surface from above; a hydrostatic sensor measures the pressure of the water above it from below. Both work in clean water, and they fail in different ways.
| Method | What disturbs it | What fails first |
|---|---|---|
| Ultrasonic (top-mounted) | Headspace temperature, condensation, foam, ladders and pipes in the beam, a blind zone close to the sensor face | False echoes after something is installed in the beam |
| Radar (top-mounted) | Fittings in the beam; air temperature does not change its signal speed | Build-up on the antenna |
| Submersible pressure | Barometric pressure if unvented, sludge over the diaphragm | A blocked or kinked vent tube in the cable |
| Float switch | Debris, biofilm, turbulence | A float stuck in one position |
One metre of water exerts about 9.81 kPa, or 0.098 bar, so a pressure sensor near the bottom reads depth directly. A vented cable lets the sensor compare against the atmosphere. An absolute sensor without that vent reads each hectopascal of weather change as about 1 cm of water, so I would specify vented gauge transmitters for open tanks.
Floats measure only a point, but they are simple and need no calibration, which makes them a good independent backup. A level reading on a screen does not replace a hard-wired high-level or dry-run cut-off on the pumps.
How to measure water level in an underground tank?
In a buried tank, a submersible pressure sensor dropped through the access hatch is usually the easier fit. An ultrasonic sensor needs a clear path to the water, enough distance to stay out of its blind zone at full level, and a dry face in a chamber where condensation is common.
Hang the pressure sensor in a stilling pipe so inflow turbulence and the cable’s swinging do not show up as level noise, above the floor sludge. Route the vent tube so water cannot run down it.
If the reading still jumps by a few centimetres, look at filtering before replacing the sensor; Sema covered it in keeping one bad reading out of your alarms.
Hermetry connects field devices to live dashboards, rules and alerts. Its Water site solution shows each tank’s level against per-tank limits: the lowLevelThreshold and highLevelThreshold attributes default to 100 cm and 560 cm, the low-level alarm needs 2 readings in a row to raise and 2 to clear with a hysteresis of 5 cm, and a tank silent for 600 seconds raises an offline warning. The tank reports its percentage itself; Hermetry does not compute it from the level.
How accurate does a reservoir level reading need to be?
Accurate enough for the decision it drives. Work out the error that decision can tolerate, in centimetres, before comparing datasheets.
Accuracy is often stated as a percentage of the sensor’s range. ±0.25% of a 10 m range is ±2.5 cm. On a 4 m tank, choosing a 5 m range instead halves that error. Multiply the error by the tank’s floor area to see what it means in volume.
Give the instrument its tag on the P&ID (see how to read a P&ID) and a line in the station’s point list, as in remote monitoring of pumping stations and reservoirs.
Frequently asked questions
Can I use an ultrasonic sensor in a drinking water tank?
Yes. A top-mounted ultrasonic or radar sensor never touches the water, which simplifies hygiene. Check that it can see the surface at both the highest and lowest levels, and that its blind zone stays above the overflow level.
Why does my pressure sensor drift with the weather?
It is probably an absolute sensor without a vent, or a vented sensor whose vent tube is blocked or wet. Each hectopascal of barometric change then shows as about 1 cm of water. Check the vent path first, then the sensor type on the datasheet.
Do I still need float switches if I have a level transmitter?
For the levels that protect equipment or prevent overflow, I would keep them. A float wired to the pump controller works when the transmitter, the network or the monitoring system does not, so a single failure does not leave the tank unprotected.

