BLE indoor asset tracking tells you which zone of a warehouse a tagged asset is in, and since when. Tags send short Bluetooth Low Energy (BLE) advertisements, readers at known places hear them, and the reader that hears a tag best names its zone. Coordinates are possible, but zone presence answers most warehouse questions.
I work on the software side of tracking for logistics sites, and I start by asking what someone will do with the answer. “This roll cage has been in dispatch for two days” leads to an action. A dot that drifts across a floor plan when a forklift passes rarely does.
How accurate is Bluetooth indoor positioning?
Signal strength gives a rough distance: good enough to tell zones apart, rarely good enough for a shelf position. The received signal strength (RSSI) falls with distance, but it also drops when a person, a forklift or a metal rack sits between tag and reader, or when the tag turns.
The Bluetooth Core specification words it carefully: path loss is often correlated with distance. So I design for zones: one reader per zone, with zone edges at walls and dock doors rather than on open floor, and no promised metre figure.
How do you track assets indoors without GPS?
Put a radio on the asset and another at a fixed point, then decide which of the two transmits. Satellite signals are weak inside steel buildings, so the GPS trackers on trailers that work in the yard are the wrong tool on the warehouse floor.
| Tags advertise, fixed readers listen | Fixed beacons advertise, the tag scans | |
|---|---|---|
| Work done by the tag | A few short transmissions per interval | Listening for every scan window, then sending its own report |
| Needs power and network | Every reader | The tag’s own uplink, for example LoRaWAN or cellular |
| Who decides the zone | The reader or the gateway behind it | The tag |
For pallets and roll cages I prefer tags that only advertise, because the tag does the least radio work. Tags that scan fit people and vehicles that also leave the building, as in yard tracking of trailers, vehicles and people.
Hermetry connects field devices to live dashboards, rules and alerts: IoT telemetry and SCADA in one platform. Its personnel tracking ready solution, built for people who wear trackers, shows who is in which zone and since when, and replays each tracker’s route over the day. Hermetry does not work out zones from positions or beacons: the tracker, or the gateway that hears it, reports the zone’s name.
How many BLE devices can one gateway handle?
The protocol sets no fixed number, because a reader that only listens needs no connection to each tag. The Core specification defines passive scanning as receive-only: the Link Layer shall not send any packets.
Every tag uses the same three primary advertising channels, and the specification shifts each advertising event by a random advDelay of 0 to 10 ms, so tags with equal intervals drift out of step. The practical limit is how many advertisements collide and how many the reader can process, so test with the real number of tags.
How does the advertising interval affect battery life?
Each advertisement costs the tag energy and tells the reader the tag is still there, so one setting decides both battery life and how fast a move shows up. Under the Bluetooth Core specification, the advertising interval is a multiple of 0.625 ms from 20 ms upward. A reader listens for a scan window in every scan interval, and when the two are equal it listens continuously, which is why I give readers mains power.
A tag has left a zone only after several advertisements were missed, which is the timeout logic I would use for any alert on missing data. Doubling the interval roughly doubles the time before a move or a missing tag is noticed.
Frequently asked questions
What should a BLE tag send besides its identifier?
Its battery level, at least. A tag with a flat battery goes quiet exactly like an asset that left the building, so a battery reading lets you replace tags before they vanish from the zone list.
How do I stop an asset flipping between two zones?
Average a few readings per reader and switch zones only when the new reader is clearly stronger for several readings in a row. Without that margin, a tag between two readers jumps back and forth with every passing forklift, and the history fills with moves that never happened.
Do BLE tags need to be paired with the reader?
No. An undirected advertisement is a broadcast that any scanner in range can receive, and a reader in passive scanning only receives. Pairing and connections are for devices that exchange data both ways, which asset tags rarely need.

