Was bedeutet "NM" neben Bauteilen in einem TI-Zigbee-Referenzschaltplan?
Von English mit KI übersetzt ·
Ich entwerfe einen Zigbee-End-Node für Bodensonden auf Basis eines TI-Referenzdesigns für den CC2652. Die Nodes kommunizieren mit einem Koordinator im Schuppen, der deren Messwerte an Hermetry weiterleitet.Mehrere Bauteile im Referenzschaltplan sind mit „NM“ markiert: zwei Kondensatoren und eine Induktivität nahe der Antenne, ein 32-kHz-Quarz mit seinen beiden Lastkondensatoren sowie ein 0-Ω-Widerstand neben einem Jumper-Footprint. Die BOM führt sie auf, aber mit Menge 0. Soll ich sie auf meine Platine bestücken oder nicht? Und falls nicht, warum sind sie überhaupt eingezeichnet?
I’m laying out a Zigbee end node for soil probes, based on a TI reference design for the CC2652. The nodes talk to a coordinator in the shed that forwards their readings to Hermetry.
Several components on the reference schematic are marked „NM“: two capacitors and an inductor near the antenna, a 32 kHz crystal and its two load caps, and a 0 Ω resistor next to a jumper footprint. The BOM lists them but with quantity 0. Do I put them on my board or not? And if not, why are they drawn at all?
Von English mit KI übersetzt ·
NM steht für „not mounted“ (nicht bestückt) und ist dasselbe wie DNP (do not populate). Der Footprint ist auf der Platine vorhanden, aber es wird kein Bauteil eingesetzt.
NM is „not mounted“, same as DNP (do not populate). The footprint is on the board but no part goes in it.
Von English mit KI übersetzt ·
Datenspezialist fragt: Die Platine hat also absichtlich leere Pads?
Data person asking: so the board has empty pads on purpose?
Von English mit KI übersetzt ·
Das verstehe ich auch nicht. Warum Pads für Bauteile vorsehen, die man gar nicht bestückt?
That’s what I don’t get either. Why put pads for parts you don’t fit?
Von English mit KI übersetzt ·
Ich habe NM bei HF-Zeichnungen immer als Nanometer gelesen, ist das falsch?
I always read NM as nanometre on RF drawings, is that wrong?
Von English mit KI übersetzt ·
Neha hat recht, und Emily, im Schaltplan ist es nicht bestückt. Ich habe einige dieser TI- und Silicon-Labs-Funkplatinen gelayoutet, und die NM-Bauteile haben jeweils einen Grund:Antennenanpassung (deine zwei Kondensatoren und die Spule): Die Anpassung hängt von deiner Leiterplatte, dem Gehäuse und der Antenne ab, deshalb legt TI ein Pi-Netzwerk-Footprint an. Du baust die Platine, misst mit einem VNA und bestückst dann die Werte, die die Antenne auf 50 Ω bringen. Manche Designs bestücken einen 0-Ω-Widerstand in Serie und lassen die Parallelbauteile bis zum Abgleich leer.32-kHz-Quarz: optional. Der Chip hat einen internen RC-Oszillator, der für viele Anwendungen ausreicht. Wenn dein Endknoten viel schläft und eine genaue Aufwachzeit braucht, bestücke den Quarz, andernfalls lass ihn weg.0-Ω- und Jumper-Footprints: Alternativen, etwa zur Wahl zwischen zwei Stromwegen oder zum Anschluss einer Debug-Schnittstelle. Das Referenzdesign hält beide Optionen offen.Für deine Bodensonden würde ich alle NM-Footprints im Layout belassen, den Quarz bestücken (schlafende Endknoten profitieren davon) und vor der Bestellung einer Charge eine Abgleichsitzung mit einem VNA im endgültigen Gehäuse einplanen. Markiere sie in der BOM als DNP, damit der Bestücker dort nichts einsetzt.
Neha’s right, and Emily, on a schematic it’s not mounted. I’ve laid out a few of these TI and Silicon Labs radio boards, and the NM parts each have a reason:
Antenna matching (your two caps and the inductor): the match depends on your PCB, enclosure and antenna, so TI leaves a pi network footprint. You build the board, measure with a VNA, and then fit the values that bring the antenna to 50 Ω. Some designs fit a 0 Ω in series and leave the shunt parts empty until tuning.
32 kHz crystal: optional. The chip has an internal RC oscillator that’s good enough for many applications. If your end node sleeps a lot and needs accurate wake timing, fit the crystal; otherwise leave it.
0 Ω and jumper footprints: alternatives, like choosing between two power paths or connecting a debug interface. The reference design keeps both options.
For your soil probes I’d keep every NM footprint on the layout, fit the crystal (sleepy end nodes benefit), and plan one tuning session with a VNA on the final enclosure before you order a batch. In your BOM, mark them DNP so the assembler doesn’t fit anything there.
Von English mit KI übersetzt ·
Das klärt es auf. Die Footprints habe ich beibehalten, den Quarz bestücke ich gerade, und für die Anpassung habe ich mir ein NanoVNA ausgeliehen, sobald die Gehäuse eintreffen. Der erste Prototyp, der nur den 0-Ω-Widerstand in Reihe nutzt, erreicht den Koordinator bereits aus 60 m, daher sollte die Abstimmung die Verbindung nur noch verbessern.
That clears it up. Kept the footprints, fitting the crystal, and borrowed a NanoVNA for the matching once the enclosures arrive. The first prototype with only the 0 Ω in series already reaches the coordinator from 60 m, so the tuning should only make it better.
- Du musst angemeldet sein, um auf dieses Thema antworten zu können.
Mitdiskutieren
Melde dich an, um Fragen zu stellen und zu beantworten, hilfreiche Beiträge mit „Gefällt mir“ zu markieren und die Antwort zu kennzeichnen, die dein Problem gelöst hat. Jeder Beitrag bringt Punkte und Stufen.

