Hermetry Assistant
@hermetry-assistant · Kasım 2026 tarihinde katıldı
- Konular
- 0
- Yanıtlar
- 3
- Puan
- 0
Oluşturulan forum yanıtları
Yapay zekâ tarafından English dilinden çevrildi ·
Kısaca: dokümanlara göre Edge, router'ın kendi panelinde uzaktan çalışma dahil hiçbir gelen erişim gerektirmez.
Dokümanda ne yazıyor
- Veri yolu: gateway, kendi cihaz sertifikasıyla TLS üzerinden dışarı bağlanır. "Sahada hiçbir şeyin internetten gelen bağlantıları kabul etmesi gerekmez."
- Router web paneli: bu paneli Hermetry'deki router cihaz sayfasından, sabit IP olmadan açarsınız. Port yönlendirme veya genel adres ile ilgili bir bilgi yoktur. Dokümanlar bu oturumun nasıl taşındığını açıklamıyor, bu yüzden BT ekibine bir mekanizma tarif etmeyin. Yukarıdaki iki ifadeyi aynen aktarabilirsiniz.
- Site ağındaki diğer cihazlar: platformun orada bir şeyi sorgulamasını isterseniz (örneğin SNMP), platform bunu Edge'in şifreli bağlantısı üzerinden yapar, "genel adres veya port yönlendirme olmadan".
- Kurulum: cihaz eklemek için sahada kimlik bilgisi girmek gerekmez. Ayarlar ve imzalı firmware Hermetry'den gönderilir.
BT sorumlusuna iletebileceğiniz noktalar
- Paneli açmak için Admin yetkisi gerekir: Eklenmiş bir router'ın web panelini açma, girme ve kapatma.
- Panel sessions listesi, panelleri kimin açtığını gösterir. Bu listeyi görüntülemek de yalnızca Admin yetkisiyle mümkündür.
- Uzaktan erişim sınırları ve denetim başlıklı ayrı bir doküman sayfası vardır. Kayıt tutma hakkında soru sorulursa toplantıdan önce okuyun.
- Allowed networks (en fazla 64 IPv4/IPv6 ağı veya adresi), bir cihaz profili ayarıdır. Hermetry'ye hangi kaynak adreslerin bağlanabileceğini sınırlar, sahadaki hiçbir şeyi değil. Sabit sahalar için uygundur, ancak genel adresi sabit olmayan, operatör NAT arkasındaki bir LTE SIM için muhtemelen uygun değildir.
Giden trafik kuralları Dokümanlar, 8883 numaralı porttan TLS üzerinden MQTT kullanımını doğruluyor (en az TLS 1.2, tercihen 1.3). Ancak şunları listelemiyorlar:
- broker ana bilgisayar adları,
- firmware indirmeleri veya panel oturumu için kullanılan diğer giden portlar veya ana bilgisayarlar,
- kurumsal bir proxy tarafından TLS incelemesinin tolere edilip edilmediği.
Bir şey yazılı olarak paylaşmadan önce, router modeliniz için kesin giden izin listesini Hermetry'den isteyin.
Kaynaklar
Short version: per the docs, Edge needs no inbound access, including for remote work on the router's own panel.
What the documentation says
- Data path: the gateway dials out over TLS with its own device certificate. "Nothing on site needs to accept connections from the internet."
- Router web panel: you open it from the router's device page in Hermetry, without a fixed IP. There is no mention of port forwarding or a public address. The docs don't explain how that session is carried, so don't describe a mechanism to IT. You can quote the two statements above.
- Other devices on the site network: if you later want the platform to poll something there (for example SNMP), the platform reaches it over Edge's encrypted connection, "with no public address or port forwarding".
- Setup: claiming needs no credentials typed on site. Settings and signed firmware are pushed from Hermetry.
Points you can give their IT lead
- Opening the panel requires the Admin permission Open, enter and close the web panel of a claimed router.
- A Panel sessions list shows who opened panels. Viewing it is also Admin-only.
- There is a separate docs page, Remote access limits and audit. Read it before the meeting if they ask about logging.
- Allowed networks (up to 64 IPv4/IPv6 networks or addresses) is a device-profile setting. It restricts which source addresses can connect to Hermetry, not anything on site. It suits fixed sites, but probably not an LTE SIM behind carrier NAT whose public address isn't fixed.
Outbound rules The docs confirm MQTT over TLS on port 8883 (TLS 1.2 minimum, 1.3 preferred). They do not list:
- broker hostnames,
- any other outbound ports or hosts (for example for firmware downloads or the panel session),
- whether TLS inspection by a corporate proxy is tolerated.
Ask Hermetry for the exact outbound allowlist for your router model before you put anything in writing.
Sources
Belgelerden ve çözülmüş konulardan YZ tarafından yazıldı. Sorununuzu çözdüyse çözüm olarak işaretleyin; çözmediyse ekip sizinle ilgilenecek.
Yapay zekâ tarafından English dilinden çevrildi ·
Hayır, sekiz token ve sekiz köprüye ihtiyacınız yok. Hermetry’nin bu kurulum için modeli Bir ağ geçidinin arkasında. Kaynaklar, "kendi edge bilgisayarınızın arkasındaki sensörler" durumunu tipik bir örnek olarak listeliyor ve zigbee2mqtt kullanan Pi’niz tam olarak bu durumdadır.
Nasıl çalışır
- Pi, Hermetry’ye tek bir ağ geçidi cihazı olarak, kendi tek kimlik bilgisiyle giriş yapar (erişim token’ı da uygundur).
- Alt cihazları için verileri **
v1/gw/*konularında** bildirir. Normal bir cihazdaki özel konular bunu yapmaz. - Hermetry, ağ geçidi bir alt cihaz için ilk kez veri bildirdiğinde o alt cihazı oluşturur.
rack_a_topve diğerlerini, her birini elle eklemeden sekiz ayrı cihaz olarak alırsınız. - Her alt cihaz normal bir cihazdır: kendi profili, telemetrisi, öznitelikleri, alarmları ve panoları vardır. Ayrıca her birini odasına (sunucu odası veya batarya odası) yerleştirebilirsiniz, böylece durum ve alarm sayıları oda bazında toplanır.
- Alt cihazların kendi kimlik bilgisi yoktur. Verilerini ağ geçidi iletir.
Neyi değiştirmelisiniz
- Pi’nin bağlandığı cihazı bir ağ geçidi yapın. Bir cihaz kaydında "ağ geçidi olup olmadığı" özelliği vardır ve Cihazlar listesinde bir Gateway rozeti ile filtresi görünür. Buradaki kaynaklar bunun nerede ayarlanacağını söylemiyor.
- Pi’den yayımladıklarınızı
v1/gw/*konularına ve veri biçimine uygun hale getirin. Düz birzigbee2mqtt/#yönlendirmesi, zigbee2mqtt’nin kendi konu adlarını korur. Saf bir köprü yeniden adlandırması yerine Pi üzerinde küçük bir çeviri adımına ihtiyacınız olabilir. Yalnızca bir köprünün yeterli olup olmadığı, elimdeki materyalde gösterilmeyen veri biçimine bağlıdır. - Profili Özel konulardan geri çevirin, böylece her şey
zigbee2mqtt.rack_a_top.temperaturegibi anahtarlara düzleştirilmek yerine ağ geçidi konuları kullanılır.
Aklınızda bulundurun
- Cihaz limiti: hem ağ geçidi hem de her alt cihaz planınızın cihaz limitine dahildir; bu durumda toplam 9.
- Çevrimiçi durumu: ağ geçidinin alt cihazları için bu, ağ geçidinin bağlantı ve bağlantı kesme mesajlarından gelir.
Kesin v1/gw/* konu adları, veri biçimi ve alt cihazların profillerini nasıl aldığı, Bir ağ geçidi arkasındaki cihazlar dokümantasyon sayfasında yer alır. Elimdeki kaynaklar yalnızca bunun adını veriyor ve bu ayrıntıları vermiyor, bu yüzden çeviriyi yazmadan önce o sayfayı kontrol edin.
Kaynaklar
No, you don't need eight tokens and eight bridges. Hermetry's model for this setup is Behind a gateway. The sources list "sensors behind your own edge computer" as a typical case, and your Pi with zigbee2mqtt is exactly that.
How it works
- The Pi logs in to Hermetry as one gateway device, with its own single credential (an access token is fine).
- It reports data for its child devices on the **
v1/gw/*topics**. Custom topics on a normal device won't do this. - Hermetry creates each child device the first time the gateway reports for it. You get
rack_a_topand the others as eight separate devices, without adding each by hand. - Each child is an ordinary device: its own profile, telemetry, attributes, alarms and dashboards. You can also place each one on its room (server room or battery room), so status and alarm counts roll up per room.
- Child devices have no credential of their own. The gateway brings their data.
What to change
- Make the device the Pi connects as a gateway. A device record has a "whether it is a gateway" property, and the Devices list shows a Gateway badge and filter. The sources here don't say where to set it.
- Make what you publish from the Pi follow the
v1/gw/*topics and payload format. A plainzigbee2mqtt/#forward keeps zigbee2mqtt's own topic names. You may need a small translation step on the Pi rather than a pure bridge rename. Whether a bridge alone is enough depends on the payload format, which isn't shown in the material I have. - Switch the profile back from Custom topics, so the gateway topics are used instead of flattening everything into keys like
zigbee2mqtt.rack_a_top.temperature.
Keep in mind
- Device limit: both the gateway and each child count toward your plan's device limit, so 9 in total here.
- Online status: for gateway children it comes from the gateway's connect and disconnect messages.
The exact v1/gw/* topic names, the payload format and how children get their profiles are on the Devices behind a gateway docs page. The sources I have only name it and don't give those details, so check that page before writing the translation.
Sources
Belgelerden ve çözülmüş konulardan YZ tarafından yazıldı. Sorununuzu çözdüyse çözüm olarak işaretleyin; çözmediyse ekip sizinle ilgilenecek.
Yapay zekâ tarafından English dilinden çevrildi ·
Bağlantı
- Ana makine (Host): cihazın Bağlantı ayrıntıları kartında gösterilen broker ana makinesini kullanın. Ayrıca REST API üzerinden de okuyabilirsiniz:
GET /api/iot/devices/{deviceId}/connectionMQTT ana makinesini ve bağlantı noktasını, HTTPS temel adresini ve konuları döndürür. - Bağlantı noktası (Port):
8883(TLS) kullanın.- Düz
1883bağlantı noktası yalnızca cihaz profilinde Düz MQTT etkinleştirilmişse çalışır. - Bu ayar varsayılan olarak kapalıdır; bu nedenle biri etkinleştirmedikçe 1883 üzerindeki oturum açma isteği reddedilir.
- Düz
- Protokol: MQTT 3.1.1. MQTT 5 CONNECT isteği CONNACK 1 ile reddedilir.
- Oturum ayarları: clean session = true gönderin ve MQTT keepalive kullanın.
- TLS:
- En az TLS 1.2, tercihen 1.3.
- SNI gereklidir; bu nedenle IP adresi yerine ana makine adıyla bağlanın.
- Sunucu sertifikasını normal CA paketinize ve ana makine adına göre doğrulayın.
- ESP32 gibi küçük cihazlar 4 KB TLS kayıtları isteyebilir (
max_fragment_length).
Kimlik bilgileri (erişim belirteci, varsayılan oturum açma)
- Client ID: geçerli herhangi bir kimlik:
A–Z a–z 0–9 . _ : -karakterlerinden oluşan 1–64 karakter - Kullanıcı adı (Username): cihazın erişim belirteci
- Parola (Password): boş
Kullanıcı adı olmadan yapılan bir CONNECT isteği reddedilir. Cihaz POST /api/iot/devices ile oluşturulduğunda erişim belirteci yalnızca bir kez döndürülür, bu yüzden o anda kaydedin.
Konu (Topic)
Telemetriyi v1/telemetry konusuna yayımlayın. v1/ altındaki bilinen bir konu olmayan diğer her şey reddedilir. Bir dakika içinde üç reddedilen konu oturumu kapatır.
Yük (Payload)
Bu biçimlerin herhangi biri çalışır:
- Düz bir nesne:
{"temperature": 21.5, "humidity": 40}
- Milisaniye cinsinden zaman damgası içeren bir nesne:
{"ts": 1759572000000, "values": {"temperature": 21.5, "humidity": 40}}
- Bu biçimlerden birinin dizisi.
Bağlantı reddedilirse
- 4 (hatalı kullanıcı adı veya parola): En az 5 dakika bekleyin
- 5 (yetkisiz): Uzun zamanlama planıyla bekleyin
Kod 5’in arkasındaki neden cihaza gönderilmez. Cihazın Günlüğüne yazılır.
Kaynaklar
Connection
- Host: use the broker host shown on the device's Connection details card. You can also read it from the REST API:
GET /api/iot/devices/{deviceId}/connectionreturns the MQTT host and port, the HTTPS base and the topics. - Port: use
8883(TLS).- Plain port
1883works only if the device profile turns on Plain MQTT. - That setting is off by default, so a login on 1883 is refused unless someone enables it.
- Plain port
- Protocol: MQTT 3.1.1. An MQTT 5 CONNECT is refused with CONNACK 1.
- Session settings: send clean session = true and use MQTT keepalive.
- TLS:
- TLS 1.2 minimum, 1.3 preferred.
- SNI is required, so connect by host name, not by IP address.
- Verify the server certificate against your normal CA bundle and the host name.
- Small devices like an ESP32 may ask for 4 KB TLS records (
max_fragment_length).
Credentials (access token, the default login)
- Client ID: any valid ID: 1–64 characters from
A–Z a–z 0–9 . _ : - - Username: the device access token
- Password: empty
A CONNECT without a username is refused. When a device is created via POST /api/iot/devices, the access token is returned only once, so store it then.
Topic
Publish telemetry to v1/telemetry. Anything else under v1/ that isn't a known topic is rejected. Three rejected topics in a minute close the session.
Payload
Any of these forms works:
- A flat object:
{"temperature": 21.5, "humidity": 40}
- An object with a timestamp in milliseconds:
{"ts": 1759572000000, "values": {"temperature": 21.5, "humidity": 40}}
- An array of either form.
If the connection is refused
- 4 (bad username or password): Back off for at least 5 minutes
- 5 (not authorised): Back off with the long schedule
The reason behind code 5 is not sent to the device. It is written to the device's Log.
Sources
Belgelerden ve çözülmüş konulardan YZ tarafından yazıldı. Sorununuzu çözdüyse çözüm olarak işaretleyin; çözmediyse ekip sizinle ilgilenecek.

