TI parça soneki sorusu: bir ağ geçidi RS-485 onarımı için ISO1410DW mi ISO1410DWR mi
Yapay zekâ tarafından English dilinden çevrildi ·
Kısa bir soru. Kendi edge kutularımızdan birinin RS-485 portunu onarıyorum (Modbus sayaçlarını sorgulayan ve bunları alt cihazlar olarak Hermetry’ye raporlayan kutu); bir voltaj dalgalanması izole alıcı-vericiyi bozdu. BOM listesinde ISO1410DWR yazıyor. Distribütörümde bugün ISO1410DW stokta var, DWR ise 6 hafta sonra. Datasheet’teki paket tablosunda D ve DW listeleniyor, R’nin ne anlama geldiği ise görebildiğim hiçbir yerde açıklanmamış. DW’yi takabilir miyim?
Quick one. Repairing the RS-485 port on one of our own edge boxes (the one that polls Modbus meters and reports them to Hermetry as child devices); a surge took out the isolated transceiver. The BOM says ISO1410DWR. My distributor has ISO1410DW in stock today and the DWR in 6 weeks. Datasheet package table lists D and DW, the R isn’t explained anywhere I can see. Can I fit the DW?
Yapay zekâ tarafından English dilinden çevrildi ·
Harfler bir sıcaklık derecesi olabilir mi? Bazı parçaların farklı bir son ekle sunulan endüstriyel sürümü var.
Could the letters be a temperature grade? Some parts have an industrial version with a different suffix.
Yapay zekâ tarafından English dilinden çevrildi ·
Uygun. Aynı parça, aynı paket. TI’nin adlandırmasında parça numarasından sonraki harfler paket kodudur; sondaki R yalnızca ambalaj şeklidir. DW geniş gövdeli SOIC-16’dır (7,5 mm gövde), D ise dar SOIC’tir (bu parçada 8 pinli olanı). Sondaki R bant ve makara anlamına gelir, genellikle 2000 adet; R yoksa tüp demektir. Veri sayfasının en sonundaki sipariş edilebilir parçalar tablosuna (“Package option addendum”) bakarsanız, her iki satır da aynı paketi ve pin sayısını gösterir; yalnızca “Package qty” farklıdır.TI parçalarında sıcaklık sınıfı, bu harflerde değil, parça numarasının gövdesinde ya da otomotiv için Q1 son ekinde yer alır.Yine de D sürümüne geçmeyin. Geniş gövde izolasyon bariyeri boyunca sürünme mesafesi için vardır; dar 8 pinli olanın izolasyon değeri daha düşüktür ve zaten farklı bir pin düzeni vardır. Kutuyu açmışken A/B üzerindeki TVS diyotlarını kontrol edin; alıcı-verici bozulduysa onlar da muhtemelen darbe almıştır.
Fit it. Same part, same package. In TI’s naming the letters after the part number are the package code, and the final R is only the packing. DW is the wide-body SOIC-16 (7.5 mm body), D is the narrow SOIC (on this part the 8-pin one). The trailing R means tape and reel, usually 2000 pieces, no R means tube. If you look at the orderable parts table at the very end of the datasheet (“Package option addendum”), both rows show the same package and pin count, only “Package qty” differs.
Temperature grade on TI parts is in the part number body or a Q1 suffix for automotive, not those letters.
Don’t swap to the D version though. The wide body is there for creepage across the isolation barrier, the narrow 8-pin one has a lower isolation rating and a different pinout anyway. Check the TVS diodes on A/B while you have it open, if the transceiver died they probably took a hit too.
Yapay zekâ tarafından English dilinden çevrildi ·
DW’yi tüpten taktım, port tekrar çalışıyor ve sayaçlar bir dakika içinde alt cihaz olarak yeniden göründü. İki TVS diyotu da kısa devre çıktı, onları da değiştirdim. Sonundaki paket tablosu konusunda haklıydın, ben sadece 1. sayfadakine bakmıştım.
Fitted the DW from the tube, port is back and the meters reappeared as children within a minute. Both TVS diodes measured short, replaced those too. You were right about the package table at the end, I’d only looked at the one on page 1.
Yapay zekâ tarafından English dilinden çevrildi ·
R meselesini öğrenmek güzel, diğer parçalarda da bunu merak etmiştim.
Good to know the R thing, I’ve wondered about that on other parts.
- Bu konuyu yanıtlamak için giriş yapmış olmalısınız.
Sohbete katılın
Soru sormak ve yanıtlamak, yararlı gönderileri beğenmek ve sorununuzu çözen yanıtı işaretlemek için oturum açın. Her katkı puan ve seviye kazandırır.

