Bir kapı sembolüne tıklama: sürücü konum, hız veya tork modunda mı çalışmalı?
Yapay zekâ tarafından English dilinden çevrildi ·
Depo ayırma kapısı, bir servo sürücü tarafından çevriliyor. Sürücü konum, hız ve tork modlarını destekliyor. Ayırıcıyı bir proses diyagramında çizdim ve operatörlerin kapıyı açmak veya kapatmak için kapı sembolüne tıklamasını istiyorum.İlk sürüm: hız modu, iki katalog komutu gate.start (bir hızla) ve gate.stop, tıklamada ve sağ tıklamada. Test tezgâhında çalıştı. Depoda durdurma komutu bir kez geç ulaştı ve kapı mekanik son durdurucuya çarptı. Bir şey kırılmadı ama beni korkuttu.Bulut tarafından gelen bir komut hangi modu kullanmalı? Üçü arasındaki pratik farkı da tam anlamadım.
Warehouse sorting gate, swung by a servo drive. The drive supports position, velocity and torque modes. I’ve drawn the sorter in a process diagram and want operators to click the gate symbol to open or close it.
First version: velocity mode, two catalog commands gate.start (with a speed) and gate.stop, on click and on right-click. It worked on the bench. In the warehouse the stop arrived late once and the gate hit its mechanical end stop. Nothing broke, but it scared me.
Which mode should a command from the cloud use? I don’t really get the practical difference between the three either.
Yapay zekâ tarafından English dilinden çevrildi ·
Düşük bir limitle tork modunu neden kullanmıyorsunuz? O zaman son durdurucuya çarpmak zarar vermez.
Why not torque mode with a low limit? Then hitting the end stop wouldn’t hurt.
Yapay zekâ tarafından English dilinden çevrildi ·
Tork modu bastırma veya gerilim tutma içindir; bir kapı yalnızca kayardı. Ve geç durma asıl dersi veriyor: hızlı bir döngüyü asla bulut üzerinden kapatmayın.Bir sembolden gelen komut geç ulaşabilir, operatör iki kez tıklayabilir ve 30 sn içinde yanıt alınamayan bir komut başarısız değil, bilinmeyen olarak gösterilir. Diyagram kartı başına aynı anda yalnızca bir komut çalışır. “Açmaya git” için sorun yok, “hareket et ve durmayı bekle” için tehlikeli.Sürücüyü konum moduna alın (ya da yanındaki küçük bir PLC hareketi yapsın). Bulut yalnızca hedef gönderir: to parametresi open veya closed olan tek bir katalog komutu gate.move. Rampayı, hız sınırını ve son konumları sürücü kendisi yönetir; böylece geç veya tekrarlanan bir komut yine aynı yerde biter. Cihazın, zaten çalıştırdığı bir istek kimliğini yok saymasını sağlayın.Sembol üzerinde: Bir komut çalıştır, Temel seviye (semboller başka bir şey gönderemez) ve onay her zaman sorulur. Kapı sembolünün durumunu sürücünün bildirdiği konuma bağlayın; böylece ekran birinin ne istediğini değil, kapının nerede olduğunu gösterir. Bakınız: Sembollerde komutlar.
Torque mode is for pressing or holding tension, a gate would just drift. And the late stop is the real lesson: never close a fast loop through the cloud.
A command from a symbol can arrive late, the operator can click twice, and a command that gets no answer within 30 s is shown as unknown, not as failed. Only one command runs per diagram card at a time. All fine for “go to open”, dangerous for “start moving and wait for stop”.
Put the drive in position mode (or let a small PLC next to it do the motion). The cloud only sends targets: one catalog command gate.move with a parameter to of open or closed. The drive does the ramp, the speed limit and the end positions itself, so a late or repeated command still ends in the same place. Make the device ignore a request id it has already run.
On the symbol: Run a command, Basic tier (symbols can’t send anything else), and the confirmation is always asked. Bind the gate symbol’s state to the position the drive reports, so the picture shows where the gate is, not what someone asked for. See Commands on symbols.
Yapay zekâ tarafından English dilinden çevrildi ·
Bunu gate.move open/closed komutlarıyla ve sürücünün kendi limitleriyle konum modunda yeniden oluşturdum. Çift tıklama testini bilerek yaptım, kapı yalnızca bir kez açık konuma gidiyor. Sembol artık bildirilen konumu takip ediyor. Ciaran’a ve Aoife’a teşekkürler, tork modu beni bir an düşündürdü.
Rebuilt it as position mode with gate.move open/closed and the drive’s own limits. Did the double click test on purpose, it just goes to open once. Symbol follows the reported position now. Thanks Ciaran, and Aoife, torque mode had me thinking for a minute.
- Bu konuyu yanıtlamak için giriş yapmış olmalısınız.
Sohbete katılın
Soru sormak ve yanıtlamak, yararlı gönderileri beğenmek ve sorununuzu çözen yanıtı işaretlemek için oturum açın. Her katkı puan ve seviye kazandırır.

