Medir 1250 °C en un horno de cerámica y recibir aviso cuando una cocción se descontrola
Traducido del English por IA ·
Pregunta de afición fuera de horario de un profesional de TI. Mi pareja tiene un horno eléctrico en el garaje que cuece a cono 6 (unos 1220 °C) y ocasionalmente a cono 10 (alrededor de 1300). El controlador del horno es antiguo y dos veces un relé se ha «pegado» y el horno se ha sobrecalentado, fundiendo una balda de piezas. Quiero una lectura de temperatura independiente en Hermetry y una alerta si supera un límite o permanece caliente demasiado tiempo.Ya tengo un ESP32 que envía la temperatura del garaje a Hermetry. Probé una sonda tipo K con un MAX6675 y marca 1023.75 y se queda ahí en cuanto el horno supera unos 1000 °C. Leyendo sobre los tipos R y S, el platino y las «vainas», me di cuenta de que no sé lo que estoy comprando.¿Qué hardware usar para la medición y cómo configurar la alarma para que no me despierte a las 2 de la mañana en cada cocción normal?
Off-hours hobby question from an IT person. My partner has an electric kiln in the garage that fires to cone 6 (about 1220 °C) and occasionally cone 10 (around 1300). The kiln’s own controller is old and twice it has «stuck» a relay and overfired, melting a shelf of work. I want an independent temperature reading in Hermetry and an alert if it goes past a limit or stays hot far too long.
I have an ESP32 already sending garage temperature to Hermetry. I tried a K-type probe with a MAX6675 and it reads 1023.75 and stays there once the kiln is past about 1000 °C. Reading online about R and S type and platinum and «sheaths» made me realise I don’t know what I’m buying.
What hardware for the measurement, and how should the alarm be set up so I don’t get woken at 2 am every normal firing?
Traducido del English por IA ·
El MAX6675 llega como máximo a 1024 °C por diseño, por eso obtienes ese 1023.75.
MAX6675 tops out at 1024 °C by design, that’s your 1023.75.
Traducido del English por IA ·
El tipo K llega más alto que eso, ¿no? ¿El único límite es el chip?
Type K goes higher than that though, right? Just the chip is the limit?
Traducido del English por IA ·
El termopar K está clasificado para unos 1260 °C, pero deriva y envejece rápido cerca del límite superior, sobre todo en una atmósfera de horno. Para el cono 10 está al límite.
K is rated to about 1260 °C but drifts and ages fast near the top, especially in a kiln atmosphere. For cone 10 it’s on the edge.
Traducido del English por IA ·
Fundo vidrio y tengo un amigo ceramista para el que monté exactamente esto, así que he revisado toda la lista de compras.Medición: usa un breakout MAX31856 en lugar del MAX6675. Lee K, pero también R y S, y cubre todo el rango. Para un horno que llega al cono 10, una sonda tipo S o R dentro de un tubo de protección de cerámica (alúmina) es lo que los fabricantes de hornos instalan ellos mismos. Es más cara que la K, pero no deriva como la K por encima de 1250 °C. Si la mayor parte del tiempo te quedas en el cono 6, una K de calibre grueso en una vaina cerámica es aceptable, solo planifica reemplazarla. Monta la sonda a través de la pared a la misma profundidad que la del propio horno para que las dos lecturas se puedan comparar.Envía kiln_c cada 30 s más o menos, además de kiln_fault desde el registro de fallos del MAX31856.Regla de alarma en el perfil, escrita en modo JSON porque quería mantener los valores de amortiguación por defecto y dos severidades:
{
"type": "kiln_overfire",
"title": "{{device.name}}: {{value}} °C",
"severities": [
{ "severity": "CRITICAL", "condition": { "key": "kiln_c", "op": ">", "value": 1290 } },
{ "severity": "MAJOR", "condition": { "key": "kiln_c", "op": ">", "value": { "attribute": "max_c" } } }
],
"debounce": { "mode": "count", "raise": 3, "clear": 3 },
"hysteresis": 15,
"enabled": true
}
max_c es un atributo del dispositivo que cambias en cada cocción (1240 para el cono 6), así que una cocción normal nunca lo toca. La línea CRITICAL es el techo de «algo va muy mal». Tres lecturas seguidas significan que un pico ruidoso no te despertará. Consulta Debounce, hysteresis and dampening.»Se mantiene caliente demasiado tiempo» no se puede hacer en una regla de alarma de perfil, ya que no puede seguir el tiempo desde que empezó la cocción. Usé una tarjeta Rules con un disparador de valor «sube por encima de 600 y se mantiene así durante» 720 minutos, y luego notificar.Y mantén un verdadero corte de sobretemperatura en el circuito de potencia del horno. La nube te avisa, pero no puede abrir el contactor si el Wi-Fi se cae.
I fuse glass and have a ceramics friend I set up exactly this for, so I’ve been through the shopping list.
Measurement: use a MAX31856 breakout instead of the MAX6675. It reads K, but also R and S, and handles the full range. For a kiln going to cone 10, an S or R type probe in a ceramic (alumina) protection tube is what kiln makers fit themselves. It’s pricier than K but doesn’t drift the way K does at 1250+. If you stay at cone 6 most of the time, a heavy-gauge K in a ceramic sheath is acceptable, just plan to replace it. Mount the probe through the wall at the same depth as the kiln’s own one so the two readings compare.
Send it as kiln_c every 30 s or so, plus kiln_fault from the MAX31856’s fault register.
Alarm rule on the profile, written in JSON mode because I wanted dampening defaults kept and two severities:
{
"type": "kiln_overfire",
"title": "{{device.name}}: {{value}} °C",
"severities": [
{ "severity": "CRITICAL", "condition": { "key": "kiln_c", "op": ">", "value": 1290 } },
{ "severity": "MAJOR", "condition": { "key": "kiln_c", "op": ">", "value": { "attribute": "max_c" } } }
],
"debounce": { "mode": "count", "raise": 3, "clear": 3 },
"hysteresis": 15,
"enabled": true
}
max_c is a device attribute you change per firing (1240 for cone 6), so a normal firing never touches it. The CRITICAL line is the «something is very wrong» ceiling. Three readings in a row means a noisy spike won’t wake you. See Debounce, hysteresis and dampening.
«Stays hot too long» can’t be done in a profile alarm rule since it can’t track time since the firing began. I used a Rules card with a value trigger «rises above 600 and stays so for» 720 minutes, then notify.
And keep a real over-temperature cutout in the kiln’s power circuit. The cloud tells you, it can’t open the contactor if the Wi-Fi is down.
Traducido del English por IA ·
¿Por qué tipo S en lugar de K a esa temperatura? ¿Es solo deriva?
why S type rather than K at that temperature? is it just drift?
Traducido del English por IA ·
He pedido un termopar tipo S en un tubo de alúmina y un MAX31856. La regla ya está activa, el truco del atributo funciona bien, esta noche he puesto max_c en 1240 y la cocción llegó a un pico de 1224 sin alarma. Un relé de sobretemperatura por hardware se instalará el próximo fin de semana, buen punto. @Aoife sobre todo la deriva y la vida útil de la sonda, por lo que he leído desde entonces.
Ordered an S type in an alumina tube and a MAX31856. Rule is in, the attribute trick works nicely, set max_c to 1240 tonight and the firing peaked at 1224 with no alarm. A hardware over-temp relay is going in next weekend, fair point. @Aoife mostly drift and the probe’s life, from what I’ve read since.
- Debes estar registrado para responder a este debate.
Únete a la conversación
Inicia sesión para preguntar y responder, dar me gusta a las publicaciones útiles y marcar la respuesta que resolvió tu problema. Cada aportación suma puntos y niveles.

