fw_owen
@owen_t42 · Se unió el abril 2026
Embedded developer · agriculture
- Temas
- 6
- Respuestas
- 20
- Puntos
- 0
Respuestas de foro creadas
Traducido del English por IA ·
Entonces, para nuestro único diseñador, que es User, crearía un grupo y marcaría designs.write para él. ¿O write necesita Admin siempre?
So for our one designer who is a User, I’d make a group and tick designs.write for it? Or does write need Admin no matter what?
Traducido del English por IA ·
Hoy conecté ota.rollout.paused a nuestro webhook de guardia. Las pausas de oleada a las 2 de la madrugada son justo lo que quiero saber.
Wired ota.rollout.paused into our on-call webhook today. Wave pauses at 2 in the morning are exactly what I want to hear about.
Traducido del English por IA ·
Dos de sus marcadores cerca de la parte superior están casi uno encima del otro. ¿Se agrupan cuando se superponen?
Two of your markers near the top are almost on top of each other. Do they group when they overlap?
Traducido del English por IA ·
Siempre supuse que WROOM era «Wireless ROOM» o algo así. Nunca lo comprobé.
I always assumed WROOM was «Wireless ROOM» or something. Never checked.
Traducido del English por IA ·
Hay un supervisor de tensión en la placa que se activa a unos 4,63 V, y el firmware lo mantiene enclavado. Se lee con vcgencmd get_throttled.
There’s a voltage supervisor on the board that trips at roughly 4.63 V and the firmware latches it. You read it with vcgencmd get_throttled.
Traducido del English por IA ·
AfcAutoOn activado, AfcBw en 41.7 kHz. Esta semana hubo tres mañanas a -1 °C y ninguna caída. El gráfico de FEI es un buen detalle, una sonda oscila 13 kHz, así que le pondrá una placa TCXO.
AfcAutoOn on, AfcBw at 41.7 kHz. This week had three mornings at -1 °C and no dropouts. The FEI chart is a nice touch, one probe swings 13 kHz, it gets a TCXO board.
Traducido del English por IA ·
Router A resuelto por teléfono con el encargado de la granja; el panel se abrió al primer intento y corregí el timeout de Modbus desde mi escritorio. El router B se actualizó solo anoche y después el panel también funcionó. Estaba en LTE y apareció el aviso de 50 MB; la sesión usó unos 6.
Router A done via phone call with the farm manager, panel opened on the first try and I fixed the Modbus timeout from my desk. Router B updated last night on its own, then the panel worked too. It was on LTE and the 50 MB prompt came up, the session used about 6.
Traducido del English por IA ·
Los números ya están listos tras dos semanas. Keepalive 300 (nuestro operador no tiene problema con ello, sin timeouts en la pestaña Log), lotes de 3, atributos solo cuando cambian. Proyección de ~9 MB por SIM al mes, frente a los 25 anteriores. La sorpresa fue el tráfico de atributos: nuestro firmware publicaba lan.ip y cell.rssi como atributos con cada lectura. Pasamos rssi a telemetría cada 15 minutos. Gracias Kevin, estas mediciones me ahorraron una semana.
Numbers are in after two weeks. Keepalive 300 (our carrier is fine with it, no timeouts in the Log tab), batches of 3, attributes only on change. Projected ~9 MB per SIM per month, down from 25. The attribute chatter was the surprise: our firmware was publishing lan.ip and cell.rssi as attributes with every reading. Moved rssi into telemetry every 15 minutes instead. Thanks Kevin, those measurements saved me a week.
Traducido del English por IA ·
Rastreamos tractores y escáneres portátiles en grandes naves, así que he revisado ambas partes.Posicionamiento: UWB con medición de distancia bidireccional. Fije de 4 a 8 anclas en paredes y columnas (más en los pasillos con estanterías) y coloque una etiqueta en cada carro (los módulos Qorvo DWM1001/DWM3000 son el punto de partida habitual). La etiqueta mide las distancias a las anclas y calcula x, y en metros en su propio sistema de coordenadas. Precisión de 10-30 cm con línea de visión. Las estanterías de piezas metálicas le restarán parte de esa precisión.La parte del panel es más fácil de lo que la gente cree. Una tarjeta Map tiene un modo Image (plano de planta): se le proporciona la imagen del plano y su ancho y alto en píxeles, y luego las columnas de latitud y longitud contienen y y x en píxeles desde la esquina superior izquierda. Así que convierta los metros a píxeles en el carro (o en la pasarela) y envíelos como dos claves:
{"pos_x_px": 812, "pos_y_px": 377, "batt_pct": 74, "job": "B12"}
En la tarjeta, configure la columna Latitude como pos_y_px y la columna Longitude como pos_x_px, coloree los marcadores según una columna de estado (idle, busy, fault) y añada campos de información emergente para la batería y el trabajo. También se pueden dibujar y reproducir las rutas si quiere saber «adónde fue el carro 7 esta mañana».La pregunta de Megan es importante por los límites. Un mensaje por carro y por segundo son 86.400 al día por cada carro, así que envíe todos los valores del carro en el mismo mensaje. El límite por defecto por dispositivo es de 10 mensajes por segundo, así que en eso no hay problema, pero revise su cuota mensual de mensajes antes de pasar a 50 carros. Map cards
We track tractors and handheld scanners in large sheds, so I’ve been through both parts.
Positioning: UWB two-way ranging. Fix 4-8 anchors on walls and columns (more in aisles with racking), put a tag on each cart (Qorvo DWM1001/DWM3000 modules are the usual starting point). The tag ranges to the anchors and computes x, y in metres in your own coordinate frame. 10-30 cm accuracy in line of sight. Racks of metal parts will cost you some of that.
The dashboard part is easier than people think. A Map card has an Image (floor plan) mode: you give it the floor plan picture and its width/height in pixels, and then the latitude and longitude columns hold y and x in pixels from the top-left corner. So convert metres to pixels on the cart (or in the gateway) and send them as two keys:
{"pos_x_px": 812, "pos_y_px": 377, "batt_pct": 74, "job": "B12"}
In the card set Latitude column to pos_y_px and Longitude column to pos_x_px, colour markers from a status column (idle, busy, fault), and add tooltip fields for battery and job. Routes can be drawn and replayed too if you want «where did cart 7 go this morning».
Megan’s question matters for limits. One message per cart per second is 86,400 a day each, so put all the cart’s values in the same message. The default per-device limit is 10 messages a second, so you’re fine there, but look at your monthly message quota before you go to 50 carts. Map cards
Traducido del English por IA ·
Un struct con int escalado lo arregló. La temperatura está limpia desde ayer por la tarde, sin huecos en el gráfico. Lo del orden de evaluación no lo sabía.
Struct with scaled int fixed it. Temperature has been clean since yesterday afternoon, no gaps on the chart. The evaluation order thing was news to me.
Traducido del English por IA ·
Funcionó en dos equipos de banco y uno en campo. Usé la mitad superior de la flash más un bootloader de 16 KB. El primer intento falló porque puse fw_title en el paquete como «irr_stm32» y el ESP32 comprobaba un guion, así que se quedó en Queued. Después de ponerle el nombre correcto, pasó a UPDATED con la nueva current_fw_version.
Got it working on two bench units and one in the field. I used the upper half of flash plus a 16 KB bootloader. First try failed because I set fw_title on the package to «irr_stm32» and the ESP32 checked for a dash, so it just sat in Queued. Named it properly and it went through to UPDATED with the new current_fw_version.
Traducido del English por IA ·
Esto es exactamente lo que necesitaba. Le dije: tenemos la capa de IoT, la parte del «4.0» para nosotros serían el árbol de activos más las acciones automáticas en los pivots, y cualquier cosa tipo MES la estudiamos por separado cuando sepa qué cubre Forge. Se quedó contento con eso, y me asignaron un ticket para desarrollar Sites & Assets para la granja norte. Gracias Maria.
This is exactly what I needed. Told him: we have the IoT layer, the «4.0» part for us would be the asset tree plus automatic actions on the pivots, and anything MES-like we look at separately once I know what Forge covers. He was happy with that, and I got a ticket to build out Sites & Assets for the north farm. Thanks Maria.
Traducido del English por IA ·
Ja, «fontanería» es probablemente la palabra que necesito para la reunión. Pero él preguntará «entonces, ¿qué lo haría 4.0?» y todavía no tengo eso.
Ha, «plumbing» is probably the word I need for the meeting. But he will ask «so what would make it 4.0» and I still don’t have that.
Traducido del English por IA ·
Una vez que se una, verá sus bytes pero no valores hasta que asigne un códec al perfil. Planifique la estructura de su payload antes de escribir el firmware.
Once it joins you’ll see your bytes but no values until you give the profile a codec. Plan your payload layout before you write the firmware.
Traducido del English por IA ·
Lado master, perdón, debí incluirlo:
Wire.requestFrom(8, 9);
m1 = (Wire.read() << 8) | Wire.read();
m2 = (Wire.read() << 8) | Wire.read();
Wire.read(); // the old byte
for (int i = 0; i < 4; i++) ((byte*)&t)[i] = Wire.read();
master side, sorry, should have included it:
Wire.requestFrom(8, 9);
m1 = (Wire.read() << 8) | Wire.read();
m2 = (Wire.read() << 8) | Wire.read();
Wire.read(); // the old byte
for (int i = 0; i < 4; i++) ((byte*)&t)[i] = Wire.read();

