Rein analoge Geräte ohne Mikrocontroller in Hermetry einbinden
Von English mit KI übersetzt ·
Ein etwas ungewöhnliches Thema. In unserem Robotik-Modul haben wir BEAM-artige Schaltungen gebaut: Lichtfolger, die nur aus Komparatoren und Transistoren bestehen, ganz ohne Mikrocontroller. Der Dozent meinte, analoge Reflexe seien schnell und einfach, aber „begrenzt“, weil sie weder kommunizieren noch sich etwas merken können.Das brachte mich auf einen realen Fall bei meinem Ferienjob: eine alte Dosieranlage mit analoger Technik, einem 4-20-mA-Füllstandsmessumformer, einem Schwimmerschalter, einer Pumpe, die pro Hub einen Impuls ausgibt, und einer Komparatorplatine, die eine Alarmleuchte schaltet. Irgendwo ein Mikrocontroller? Fehlanzeige. Der Betriebsleiter möchte die Anlage wie die neueren Anlagen in Hermetry sehen. Ist das „kein MCU“ wirklich eine Sackgasse, oder gibt es eine Möglichkeit, diese Art von Geräten auszulesen, ohne sie neu zu konstruieren?
Bit of an odd one. In our robotics module we built BEAM-style circuits: light followers made only from comparators and transistors, no microcontroller at all. The lecturer’s point was that analog reflexes are fast and simple, but „limited“, because they can’t communicate or remember anything.
That got me thinking about a real case at my summer job: an old dosing skid with analog gear, a 4-20 mA level transmitter, a float switch, a pump that gives a pulse output per stroke, and a comparator board that switches an alarm lamp. No microcontroller anywhere. The supervisor wants it on Hermetry like the newer skids. Is the „no MCU“ thing really a dead end, or is there a way to read this kind of equipment without redesigning it?
Von English mit KI übersetzt ·
Viele unserer Zählern in den Straßenschränken liefern nur Impulse, und sie melden trotzdem zuverlässig; es muss nur jemand diese Impulse zählen.
Plenty of our street cabinet meters only give pulses and they report fine, something just has to count them.
Von English mit KI übersetzt ·
Überhaupt keine Sackgasse, der „kommunizierende“ Teil wandert einfach in eine Box daneben. Wir haben eine Pressenlinie aus den 90ern, die so meldet.Hermetry Edge läuft auf lizenzierten Gateways und liest Feldgeräte vor Ort aus, unter anderem Modbus RTU über RS-485 und Modbus TCP, je nach Gateway-Modell. Du stellst also ein Analog-zu-Modbus-E/A-Modul neben das Skid: 4-20-mA-Eingang für den Füllstand, einen digitalen Eingang für den Schwimmer und einen Zählereingang für die Pumpenimpulse. Edge liest das Modul aus, und jedes Feldgerät erscheint in Hermetry als eigenes untergeordnetes Gerät mit Messwerten, Alarmen und Dashboards. Das Gateway wählt sich per TLS mit einem eigenen Zertifikat ein, du beanspruchst es mit dem Code von seiner lokalen Cloud-Seite.Impulszählung direkt über die digitalen Eingänge des Gateways hängt vom Modell ab, prüfe daher zuerst die Spezifikation des Modells. Zählt es nicht, übernimmt das E/A-Modul die Aufgabe.Der Komparator der Alarmlampe kann so bleiben, wie er ist. Verbinde seinen Ausgang zusätzlich mit einem digitalen Eingang, damit du den Lampenzustand aus der Ferne siehst.Was du von analogen Geräten nicht bekommst: Zeitstempel, lokale Logik und Pufferung am Sensor. Das Gateway ergänzt die Zeit beim Auslesen, und lizenzierte Gateways können bei unterbrochener Verbindung puffern, wie viel davon möglich ist, hängt aber vom Modell ab. Lies Licensed gateways and Hermetry Edge, bevor du dich für eines entscheidest.
Not a dead end at all, the „communicating“ part just moves to a box next to it. We have a press line from the 90s that reports like this.
Hermetry Edge runs on licensed gateways and reads field devices on site, Modbus RTU over RS-485 and Modbus TCP among them, depending on the gateway model. So you put an analog-to-Modbus I/O module next to the skid: 4-20 mA input for the level, a digital input for the float, and a counter input for the pump pulses. Edge reads the module and each field device shows up in Hermetry as its own child device with readings, alarms and boards. The gateway dials out over TLS with its own certificate, you claim it with the code from its local Cloud page.
Pulse counting directly on the gateway’s own digital inputs depends on the model, so check the model’s specification first. If it doesn’t count, the I/O module does.
The alarm lamp comparator can stay as it is. Wire its output into a digital input too, so you see the lamp state remotely.
What you don’t get from analog gear: timestamps, local logic and buffering at the sensor. The gateway adds the time when it reads, and licensed gateways can buffer while the link is down, but how much depends on the model. Read Licensed gateways and Hermetry Edge before you pick one.
Von English mit KI übersetzt ·
Das ist für meinen Betreuer eine viel bessere Antwort als „neu entwerfen“. Das Gateway-Modell, das sie sich ansehen, zählt Impulse, also geht die Pumpe direkt rein, und Füllstand und Schwimmer laufen über ein E/A-Modul. Außerdem werde ich das in meinem BEAM-Aufsatz zitieren: analoger Reflex plus eine Box, die kommunizieren kann.
That’s a much better answer for my supervisor than „redesign it“. The gateway model they’re looking at counts pulses, so the pump goes straight in and the level and float go through an I/O module. Also going to quote this in my BEAM essay, analog reflex plus a box that talks.
- Du musst angemeldet sein, um auf dieses Thema antworten zu können.
Mitdiskutieren
Melde dich an, um Fragen zu stellen und zu beantworten, hilfreiche Beiträge mit „Gefällt mir“ zu markieren und die Antwort zu kennzeichnen, die dein Problem gelöst hat. Jeder Beitrag bringt Punkte und Stufen.

