brian14
@russo-b · Aralık 2025 tarihinde katıldı
IT and security admin · energy
- Konular
- 4
- Yanıtlar
- 7
- Puan
- 0
Oluşturulan forum yanıtları
Yapay zekâ tarafından English dilinden çevrildi ·
Teşekkürler, açıklama yöneticim için yazmama yardımcı oldu. Her 2 dakikada bir, 4 okumalı tek bir mesajda toplu gönderim yapıldı ve önce keepalive 90 s olarak ayarlandı: bir hafta boyunca keepalive zaman aşımı yaşanmadı. Köprü üzerindeki saha AP’si gelecek ay için onaylandı.
Thanks, the explanation helped me write it up for my manager. Batched to one message every 2 minutes with 4 readings and keepalive 90 s first: no keepalive timeouts in a week. The yard AP on a bridge is approved for next month.
Yapay zekâ tarafından English dilinden çevrildi ·
2.4 GHz, 20 MHz kanallar. ESP32 zaten 5 GHz’i desteklemiyor.
2.4 GHz, 20 MHz channels. The ESP32 can’t do 5 GHz anyway.
Yapay zekâ tarafından English dilinden çevrildi ·
Yüksek önem derecesindeki olayları API’yi sorgulamak yerine SIEM sistemimize itmeyi tercih ederiz. Bunun için bir hook var mı?
We’d rather push high severity events into our SIEM than poll the API. Any hook for that?
Yapay zekâ tarafından English dilinden çevrildi ·
SDN pininde bağlantı yoktu (floating). Kütüphanedeki pine bağlayınca başlatma ilk denemede başarılı oldu. Verici depoda, alıcı ise satırları USB üzerinden Pi’ye ileten ikinci bir Pro Mini üzerinde; 900 m mesafe, RSSI yaklaşık -95. Tank seviyesi Hermetry içinde tank.level_cm olarak tutuluyor. Eric’e teşekkürler, güç sınırlarıyla ilgili hatırlatması için Maria’ya da teşekkürler, gücü geri çektim.
SDN was floating. Tied it through the library pin and init succeeded on the first try. Sender at the tank, receiver on a second Pro Mini that passes lines to the Pi over USB, 900 m with RSSI around -95. Tank level is in Hermetry as tank.level_cm. Thanks Eric, and Maria for the reminder about power limits, I backed it off.
Yapay zekâ tarafından English dilinden çevrildi ·
Çözüldü. Interfaces dosyası temizlendi, dhcpcd.conf içinde noipv4ll ile statik yapılandırma yapıldı. Bu sabah Pi’yi arka arkaya on kez yeniden başlattım ve gateway her seferinde birkaç saniye içinde bağlandı. Log sekmesinde artık her açılışta tek ve temiz bir bağlantı görünüyor.
Fixed. Interfaces file cleaned, static config in dhcpcd.conf with noipv4ll, rebooted the Pi ten times in a row this morning and the gateway connected within a few seconds every time. The Log tab now shows one clean connect per boot.
Yapay zekâ tarafından English dilinden çevrildi ·
Evet, ifdown interface eth0 not configured çıktısı veriyor ve ardından ifup da aynı şekilde başarısız oluyor.
Yes, ifdown says interface eth0 not configured and ifup fails the same way afterwards.
Yapay zekâ tarafından English dilinden çevrildi ·
Çek valfleri tuttuk (bakım sorumlusu jessicathompson37 ile hemfikir oldu). Kompresör 2 borumu, tahmin ettiğiniz gibi, receiver’dan çizmiştim. İkisini de kompresörlerden yeniden çizdim; artık yalnızca çalışan olan animasyon gösteriyor. Kompresör sembolleri, satın alma ekibine Process kütüphanesini sormamızdan sonra göründü, elimizde yalnızca temel set vardı. Bypass eklendi.
Kept the check valves (maintenance lead agreed with jessicathompson37). My compressor 2 pipe was drawn from the receiver, as you guessed. Redrew both from the compressors, now only the running one animates. Compressor symbols appeared after purchasing asked about the Process library, we had only the core set. Bypass added.

