Unsere RFM95-Platine empfängt das Gateway 17 dB schlechter als das Dev-Board
Von English mit KI übersetzt ·
Ich bin IT-Mensch und rutsche gerade in die Hardware ab, also bitte nachsichtig sein. Ich habe eine kleine 2-Lagen-Platine mit einem RFM95W (868 MHz) für Tankfüllstandssensoren entworfen. Vom ANT-Pin des Moduls bis zum U.FL-Steckverbinder sind es etwa 6 mm Leiterbahn. Gleiche Firmware, gleiche Antenne, gleicher Standort: Das Dev-Board erreicht das Gateway mit -98 dBm, meine Platine mit -115. Im Frame-Log hat meine außerdem einen SNR von etwa -4, während das Dev-Board bei +7 liegt.Brauche ich bei einer so kurzen Leiterbahn eine Impedanzanpassung? Ich dachte, 6 mm bei 868 MHz seien zu kurz, um eine Rolle zu spielen.
IT person drifting into hardware, so be gentle. I designed a small 2-layer board with an RFM95W (868 MHz) for tank level sensors. From the module’s ANT pin to the U.FL connector is about 6 mm of trace. Same firmware, same antenna, same spot: the dev board reaches the gateway at -98 dBm, mine at -115. In the frames log mine also has SNR around -4 where the dev board sits at +7.
Do I need impedance matching on a trace this short? I thought 6 mm at 868 MHz was too short to matter.
Von English mit KI übersetzt ·
6 mm sind bei 868 MHz elektrisch kurz, die Anpassung dürfte Sie nicht 17 dB kosten. Suchen Sie woanders.
6 mm is electrically short at 868, matching shouldn’t cost you 17 dB. Look elsewhere.
Von English mit KI übersetzt ·
Ist die Antenne tatsächlich eine für 868 MHz? Die für 915 MHz sehen genauso aus.
Is the antenna actually an 868 one? The 915 ones look the same.
Von English mit KI übersetzt ·
868, dasselbe, das ich auf dem Dev-Board verwende.
868, same one I use on the dev board.
Von English mit KI übersetzt ·
Kurz hilft, aber 17 dB sind nicht „kurze Leiterbahn“-Bereich, das ist ein defekter HF-Pfad. Hatte das bei einer Sensorplatine für ein Reinraum-Monitoring und habe etwa denselben Verlust gehabt.Fragen zum Prüfen: Liegt unter der Leiterbahn auf der anderen Lage eine durchgehende Masse? Ist die Leiterbahn 50 Ohm? Bei 1,6 mm FR4 ist eine 50-Ohm-Microstrip etwa 3 mm breit, daher hat eine 0,25 mm breite Signalleitung eher etwa 120 Ohm. Über 6 mm erklärt das allein nicht die ganzen 17 dB, aber ohne Masseebene darunter wird die Leiterbahn zur halben Antenne, die in Ihre eigene Platine abstrahlt.Was ich bei der nächsten Revision machen würde: Coplanar Waveguide mit Masse auf beiden Seiten und einer Reihe von Vias, Breite aus einem Rechner für Ihren Lagenaufbau, ein Pi-Netzwerk-Footprint zwischen Modul und Steckverbinder (0 Ohm in Serie, die anderen nicht bestückt, bis Sie messen können), und die U.FL-Massepads direkt mit der Ebene vernäht. Den Schaltregler von dieser Ecke fernhalten.Dann vergleichen Sie erneut im Frames-Log, es zeigt den besten RSSI und SNR pro Uplink, damit Sie beide Boards am selben Gateway ohne zusätzliche Werkzeuge prüfen können. Siehe The frames log.
Short helps, but 17 dB is not „short trace“ territory, that’s a broken RF path. Did this on a sensor board for a cleanroom monitor and lost about the same.
Questions to check: is there solid ground under the trace on the other layer? Is the trace 50 ohm? On 1.6 mm FR4 a 50 ohm microstrip is around 3 mm wide, so a 0.25 mm signal trace is closer to 120 ohm. Over 6 mm that alone isn’t the whole 17 dB, but add no ground plane under it and the trace is half an antenna radiating into your own board.
What I’d do on the next revision: coplanar waveguide with ground on both sides and a row of vias, width from a calculator for your stackup, a pi network footprint between module and connector (0 ohm in series, others not fitted until you can measure), and the U.FL ground pads stitched straight to the plane. Keep the switching regulator away from that corner.
Then compare again in the frames log, it shows the best RSSI and SNR per uplink so you can check both boards on the same gateway without extra tools. See The frames log.
Von English mit KI übersetzt ·
Die Unterseite unter der Leiterbahn war leer, ich hatte die Batterieleitung dort durchgeführt. Rev B: CPWG mit 50 Ohm, Via-Zaun, Masse durchgehend. Jetzt -100 dBm und SNR +6 an derselben Stelle. Danke Laura.
Bottom layer under the trace was empty, I had routed the battery line through there. Rev B: CPWG at 50 ohm, via fence, ground solid. Now -100 dBm and SNR +6 at the same spot. Thanks Laura.
- Du musst angemeldet sein, um auf dieses Thema antworten zu können.
Mitdiskutieren
Melde dich an, um Fragen zu stellen und zu beantworten, hilfreiche Beiträge mit „Gefällt mir“ zu markieren und die Antwort zu kennzeichnen, die dein Problem gelöst hat. Jeder Beitrag bringt Punkte und Stufen.

